How to Fix a HIKVISION Camera Not Displaying or Losing Connection

HIKVISION cameras are among the most popular surveillance devices worldwide, known for their excellent image quality and reliability. However, a common issue many users face is the camera not displaying or losing connection. Don’t worry! In this guide, we’ll walk you through step-by-step solutions to troubleshoot and resolve this problem—even if you’re not a tech expert.

Common Causes

Before diving into fixes, let’s look at the typical reasons behind this issue:

Unstable Power Supply: The camera isn’t getting enough power from the adapter or PoE switch.
Faulty Cables: Loose, damaged, or poor-quality network or power cables.
Network Misconfiguration: IP address conflicts or mismatch with the recorder (NVR/DVR).
Device Freeze: The camera or recorder needs a reboot or reset.
Hardware Failure: The camera or recorder may be defective after prolonged use.

Step-by-Step Troubleshooting Guide

Step 1: Check the Power Supply

For cameras with an adapter:
- Ensure the adapter (typically 12V) is securely plugged in.
- Use a multimeter to verify the adapter is delivering the correct voltage. If not, replace it.
For PoE-powered cameras (Power over Ethernet):
- Confirm that the PoE switch or NVR has PoE enabled.
- Test the camera on a different PoE port to rule out a faulty port.
Quick Tip: If the camera’s LED isn’t on, the issue is likely power-related.

Step 2: Inspect the Cables

Network Cable (Ethernet):
- Verify the cable follows the T568B standard (commonly used for camera systems).
- Test with a new cable or use a cable tester to check for internal breaks.
Power Cable (if using an adapter):
- Check if the connector is loose or if the cable shows signs of damage (e.g., chewed by rodents).
Pro Tip: If the distance between the camera and recorder exceeds 100m (with Cat5e), signal loss may occur. Use higher-quality Cat6 cables or add a repeater.

Step 3: Restart the Devices

Restart the Camera:
- Unplug the power (adapter or PoE) for 10-15 seconds, then reconnect it.
Restart the Recorder:
- Access the NVR/DVR menu (if possible) and select “Restart,” or unplug and replug the power.
This simple step often resolves temporary glitches.

Step 4: Verify Network Settings with SADP

Download the SADP (Search Active Device Protocol) tool from the official HIKVISION website: www.hikvision.com.
How to Use It:
1. Install and launch SADP on a computer connected to the same network as the camera.
2. The tool will scan and list all HIKVISION devices on the network.
3. If the camera shows as “Inactive,” select it, enter a password to activate it.
4. Check if the camera’s IP matches the recorder’s network (e.g., both in the 192.168.1.x range).
5. If there’s an IP conflict or mismatch, adjust the camera’s IP (e.g., to 192.168.1.100) and click “Save.”
Note: If the camera doesn’t appear in SADP, recheck the network cable or consider resetting the camera.

Step 5: Reset the Camera to Factory Settings (if Necessary)

If all else fails, resetting the camera might be your last resort:
- Locate the reset button (usually a small pinhole; press and hold for 10-15 seconds while powered on).
- After resetting, the camera reverts to default settings and will need reconfiguration via SADP or the recorder.
Warning: Resetting wipes all previous settings, so note down your configuration details beforehand if possible.

Step 6: Test for Hardware Issues

If the camera still doesn’t work:
- Swap it with another camera at the same spot to determine if the issue lies with the camera or the recorder.
- Contact HIKVISION support or your local distributor for warranty service if the device is still covered.

Tips to Prevent Future Issues

Use a stable power source (like a UPS) to protect against voltage drops.
Regularly update the firmware for your camera and recorder from HIKVISION’s official site.
Keep a record of passwords and network settings for easier troubleshooting.

Conclusion

The “HIKVISION camera not displaying or losing connection” issue can usually be fixed at home with simple checks like power, cables, or network reconfiguration. If you’ve tried these steps and still face problems, don’t hesitate to reach out to HIKVISION’s technical support or your local distributor

Feel free to leave a comment if you need more detailed guidance or want to share your own experience with this issue!

Tutorial